Heat Pump Pool & Spa Heater - globalimageserver.com

Loading...

INSTALLATION & OPERATING INSTRUCTIONS

Heat Pump Pool & Spa Heater Professional Series PS10353ti-E-HC PS10354ti-E-HC PS10355ti-E-HC R

C

LI S

TED

US

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids or other combustible materials in the vicinity of this or any other appliance. To do so may result in an explosion or fire. NOTE: The instructions in this manual are for the use of qualified individuals specially trained and experienced in the installation and maintenance of this type of equipment and related system components. Installation and service personnel are required by some states to be licensed. Persons not qualified shall not attempt to install, service, or maintain this equipment. This manual should be maintained in legible condition and kept adjacent to the heat pump pool heater or in a safe place for future use. Catalog No. 6000.554A

Effective: 06-28-13

Replaces: 12-21-11

P/N 241460 Rev. 2 92-103778-07-02

Rev. 2 reflects the following: Changes to: Installation Considerations on pages 6-7, Hurricane Tie Down Requirements diagram on page 8, Table C on page 14, Wiring diagrams on pages 19-21. Additions: None. Deletions: None.

2

Water Chemistry (Corrosive water voids all warranties) For your health and the protection of your pool equipment, it is essential that your water be chemically balanced. The following levels must be used as a guide for balanced water. Recommended Level(s)

Water Temp. (Deg. F) pH

Total Alkalinity (PPM)

Calcium Hardness (PPM) Salt (PPM)

Free Chlorine (PPM)*

Total Dissolved Solids (PPM)

Fiberglass Pools

Fiberglass Spas

Other Pool & Spa Types

7.3 to 7.4

7.3 to 7.4

7.6 to 7.8

68 to 88

89 to 104

68 to 104

120 to 150

120 to 150 150 to 200

200 to 400

4500 MAXIMUM

4500 MAXIMUM

4500 MAXIMUM

3000 MAXIMUM**

3000 MAXIMUM**

3000 MAXIMUM**

200 to 300 2 to 3

2 to 3

80 to 120

2 to 3

*Free Chlorine MUST NOT EXCEED 5 PPM! ** In salt water chlorinated pools, the total TDS can be as high as 6000ppm. •

• •

Occasional chemical shock dosing of the pool or spa water should not damage the heater providing the water is balanced.

Automatic chemical dosing devices and salt chlorinators are usually more efficient in heated water. Unless controlled, they can lead to excessive chlorine level which can damage your heater.

Further advice should be obtained from your pool or spa builder, accredited pool shop, or chemical supplier for the correct levels for your water.

3

CONTENTS Water Chemistry Warnings Pay Attention to These Terms Introduction Installation Considerations Electrical Connections Water Connections Pressure Drop Controls Operating Instructions To Select Pool or Spa Mode To Increase the Desired Water Temperature (Pool or Spa Mode) To Lower Desired Water Temperature (Pool or Spa Mode) To Select Temperature in °C or °F Heat/Cool Operation System Start-Up Seasonal Start-Up or Annual Check Summer Shutdown Freeze Protection

System Drain-Down Continuous Pump Operation Maintenance Air Coil Cleaning Cabinet Care (optional) Unplug Condensation Drain Holes Troubleshooting Service Call Verification Power Supply Water Flow Time Clock Adjustment Plumbing Diagrams Wiring Diagram — 208V/230V Three-Phase — 60 Hz Wiring Diagram — 460V Three-Phase — 60 Hz Wiring Diagram — 380V Three-Phase — 60 Hz Installing a Remote Control Device Wiring Heater Settings

3 5 5 6 6 7 9 9 10 10 10 10

10 10 11 11 11 11 12

4

12 12 12 12 12 12 12 13 13 13 14 15 19 20 21 22 22 22

Warnings DANGER: WARNING: CAUTION: NOTE:



Pay Attention to These Terms

Indicates the presence of immediate hazards which will cause severe personal injury, death or substantial property damage if ignored.

Indicates the presence of hazards or unsafe practices which could cause severe personal injury, death or substantial property damage if ignored.

Indicates the presence of hazards or unsafe practices which could cause minor personal injury or product or property damage if ignored.

Indicates special instructions on installation, operation, or maintenance which are important but not related to personal injury hazards.

This manual, as well as the pool/spa heat pump pool heater itself, contains ANSI-approved product safety signs and labels. Please read these signs and labels, as they convey important safety information about hazards that may be potentially present in and around the heat pump pool heater. CAUTION: Elevated water temperature can be hazardous. The U.S. Consumer Product Safety Commission has these guidelines:

CAUTION: Improper chemical content in a swimming pool or spa can damage the heat pump pool heater. DO NOT add pool chemicals to the skimmer. This will damage the heat pump pool heater and could void the heat pump pool heater warranty. ALWAYS follow the product manufacturer’s directions when adding any chemicals to your pool.

2. Drinking of alcoholic beverages before or during spa or hot tub use can cause drowsiness which could lead to unconsciousness and subsequently result in drowning.

WARNING: These heat pump pool heaters are charged with R-410A refrigerant. Ensure that all service work is done with gauges and equipment suitable for R-410A.

1. Spa water temperatures should never exceed 104°F (40°C). A temperature of 100°F (38°C) is considered safe for a healthy adult. Special caution is suggested for young children.

3. Pregnant Women Beware! Soaking in water over 102°F (39°C) can cause fetal damage during the first three months of pregnancy resulting in the birth of a brain-damaged or deformed child. Pregnant women should stick to the 100°F (38°C) maximum rule.

4. Before entering the spa or hot tub, users should check the water temperature with an accurate thermometer; spa or hot tub thermostats may err in regulating water temperatures by as much as 4°F (2.2°C).

5. Persons with a medical history of heart disease, circulatory problems, diabetes, or blood pressure problems should obtain a physician's advice before using pools or hot tubs.

6. Persons taking medications which induce drowsiness, such as tranquilizers, antihistamines, or anticoagulants, should not use spas or hot tubs.

5

Introduction

Installation Considerations WARNING: Do not install the unit within 3 ft of fossil fuel burning heaters. Air intake along the sides of this heat pump pool heater could disturb the combustion process of the unit, and could cause damage or personal injury. • Mount the unit on a level, sturdy base, preferably a concrete slab or blocks. The size of the base should be at least 3 ft by 3 ft. • You must install the 4 black rubber sound isolation pads (each 2 inches square) that ship with the unit. The pads are shipped in a bag with the unions, gaskets and the I&O manual. Install pads under the 4 corners of the unit to reduce vibration and sound transmission to the base.

WARNING: This pool/spa heat pump pool heater is an electromechanical machine that incorporates a pressurized refrigerant gas in a sealed system. ONLY trained and qualified service personnel are authorized to install or service this equipment. Without proper training and knowledge of such equipment, any attempt to install or service the unit could result in serious injury or even death. This manual contains important information on the use, maintenance and troubleshooting of your new heat pump pool heater. This unit must be properly installed, maintained and operated for optimal performance.

This heat pump pool heater is an extremely efficient, economical machine designed specifically for swimming pool heating. It is similar in design and operation to a typical residential air conditioning system. The unit employs a hermetic motor/compressor operating in a refrigeration cycle to extract heat from ambient air and deliver it to the circulating pool water.

CAUTION: The unit’s supporting base must be high enough to keep it completely free of standing water at all times. Situate the heat pump pool heater carefully to minimize installation costs while providing maximum efficiency of operation, and to allow adequate service access, as follows:

As with all heat pump pool heaters, compared to other types of heaters such as gas or oil-fired, this heat pump pool heater has lower heating capacity on a BTUH/hr basis. As a result, it will be required to operate longer to accomplish the desired results. It may, at certain times, operate as much as 24 hours per day. However, this should not be of concern to the owner, because the unit is designed to operate continuously. Even though it may operate continuously for many hours, it will still heat the pool with greater economy than other types of fossil fuel heaters.



For unrestricted air intake and service access, position each side of the unit at least 1 ft (30 cm) from walls, pipes and other obstructions.

WARNING: This unit is designed for outdoor installation; DO NOT install it in an enclosed area such as a shed or garage. •

Place a cover or blanket over the pool at night and other non-use periods. This will keep evaporation, the cause of main heat loss, to a minimum, and will greatly reduce pool heating costs. During warmer weather, the cover may be required only at night.



• •

6

Recirculation of cold discharge air back into the evaporator coil will greatly reduce the unit’s heating capacity and efficiency.

This unit features an ‘up-flow’ discharge for quiet operation. Air is pulled up through the evaporator coil and discharged through the top grill. Allow at least 5 ft (1.5 m) clearance above the unit for unrestricted air discharge. DO NOT install the unit under a porch or deck. Refer to Fig. 1. To minimize water piping, locate the unit as close as possible to the existing pool pump and filter.

If the location of the heat pump pool heater is below the water line of the pool, the water pressure switch might need to be adjusted or an external water flow switch might be needed.

60” MIN

3 FT MIN

GAS HEATER

• •







AIR FLOW OUT

12” MIN

AIR FLOW IN

AIR FLOW IN

Fig. 1: Installation Clearances

Irrigation water should be directed away from the heat pump pool heater-water spray can damage the heat pump pool heater.

All wiring must be in accordance with the National Electrical Code, NFPA No. 70, latest edition, and all applicable state and local codes. Wiring diagrams are located on pages 19 through 21.

Rain water run offs- the heat pump pool heater can withstand normal rain. Install rain gutters to prevent direct steams of rain water to the heat pump pool heater.

It is important to keep the area next to the heat pump pool heater clear of shrubs, bushes and chemicals containers. They could prevent air from circulating fully through the heat pump pool heater, and will affect the operation of the heat pump pool heater or damage the heat pump pool heater.





When installed in areas where freezing temperatures can be encountered, drain the water circuit to prevent possible freeze-up damage. See the Freeze Protection Section.



For high wind installation requirements, refer to the diagram on page 8.

Electrical Connections

NOTE: Refer to the National Electrical Code, Article 680, for general requirements for swimming pools and equipment, and to Article 440 for special considerations necessary for circuits supplying hermetic refrigeration motor/compressors.

Locate the equipment disconnect means within 3 feet of the heater’s electrical enclosure, or as close to the heater as possible. Always satisfy applicable codes and standards.

In sizing power wiring, be especially aware of upsizing requirements necessary due to wiring distances. Always satisfy applicable codes and standards.

Electrical installation should be done by a licensed electrician only.

This unit is pre-wired to work with external control systems, heat-on-demand options and other external time clock overrides. Refer to the external control system’s instructions, and page 22 of this manual, for installation information.

Refer to the unit rating plate below the control panel for precise power requirements for your unit, and for ampacity and over-current protection requirements. 7

8

SEE HIGH WIND LOAD RESTRAINT DETAIL 1

COVERED UNIT HEIGHT BETWEEN 37-1/2” - 49-3/4” NOT INCLUDING ISOLATOR PADS

GREATER THAN OR EQUAL TO 4” THICK SOLID CONCRETE 3000 P. S. I. OR GREATER LOAD RATING PAD LENGTH GREATER THAN OR EQUAL TO UNIT LENGTH +6” PAD WIDTH GREATER THAN OR EQUAL TO UNIT WIDTH +6”

PAD SPECIFICATION:

THIS DRAWING USED AS A GRAPHICAL REPRESENTATION ONLY AND IT MAY NOT APPEAR EXACTLY LIKE YOUR SPECIFIC UNIT.

2-1/2” MIN. SPACING TYP.

27” MIN 32” MAX RESTRAINT SPACING

(4) VIBRATION ISOLATION PADS TYP. EA. CORNER

UNIT

(2) 1/4” CONCRETE SCREWS LENGTH TO PENETRATE 2-3/8” MINIMUM. HIGH WIND LOAD RESTRAINT DETAIL 1

CONCRETE PAD (SEE PAD SPECS.)

CL

MINIMUM 18 GA. X 5” WIDE GALV. STEEL STRAP (G90) OR EQUIVALENT (MIN. QTY. OF 4 STRAPS) WITH (3) 1/2” LONG #12 SELF DRILLING SCREWS EACH STRAP (MIN. 1000 HR. COATING)

186 MPH, 3 SEC. GUST IN ACCORDANCE WITH: ASCE 7-2010 CHAPTER 30 WIND LOADS - COMPONENTS AND CLADDING FLORIDA BUILDING CODE 2010 - SECTION 1609 WIND LOADS FLORIDA BUILDING CODE 2010 - SECTION 1620 HIGH VELOCITY HURRICANE ZONES - WIND LOADS

Model No.

VAC - Phase - Hz

Minimum Circuit Ampacity (A)

Maximum Breaker Size (A)

10353

208/230 - 3 - 60

42.0

70

10354

460 - 3 - 60

26.0

40

10355

380 - 3 - 60

29.0

45

Table A: Typical System Electrical Power Requirements

Water Connections

CAUTION: The heat pump pool heater inlet and outlet connections are NOT interchangeable. They must be connected as instructed below.

WATER IN

1. Connect the heat pump pool heater in the return water line between the filter and the pool/spa. See the Plumbing Diagrams beginning on page 15.

Fig. 2: Water Connections

2. Connect the filter outlet to the fitting marked WATER IN at the bottom front of the unit.

4. In cold weather (freeze zone) areas, shutoff valves (ball or gate type) must be installed at the unit inlet and outlet to facilitate service and cold weather drain-down.

3. Connect the fitting marked WATER OUT to the return piping to the pool/spa. Unit inlet/outlet connection fittings are 2-inch PVC unions.

5. Operate the pump and check the system for leaks.

Pressure Drop

Water connections from the unit to the main return line can be PVC pipe or flexible pipe approved for the purpose and, in either case, should be at least equal in size to the main pool/spa circulation piping. Flow (gpm)

10353HC

40

10

30 50

10

WATER OUT

For system pressure drop information, refer to Table B below.

Pressure Drop (psi) 10354HC

10355HC

10

10

10

11

11

10 11

60

12

12

12

80

14

14

14

70

13

13

13

Note: Multiply the pressure drop in psi by 2.3067 to yield the pressure drop in Ft. H2O Head (TDH).

Table B: Pressure Drop Across Heat Pump Pool Heater

9

Operating Instructions

WARNING: Install a check valve and/or a Hartford loop AFTER the heat pump pool heater and BEFORE any chlorinating devices. Install any automatic chemical feeders AFTER the heat pump pool heater. Improper installation of any type of automatic chemical feeders can result in serious damage to, or premature failure of, the heat pump pool heater and will void the heat pump pool heater warranty.

The electronic board has the capability of memorizing two different programmed temperature settings as follows (refer to Fig. 5): •



Controls

For a pool, maximum 95°F (35°C)

For a spa, maximum 104°F (40°C)

To Select Pool or Spa Mode

Your heat pump pool heater incorporates digital safety controls and indicators to ensure its safe, reliable operation.

To have access to either one of these programs, press the SET key until you see P _S and by pressing the UP or DOWN key you can switch to POL or SPA.

Water Pressure Switch: Prevents operation when the pump is OFF. The unit requires 5 psi minimum pressure.

To Increase the Desired Water Temperature (Pool or Spa Mode)

Push the SET key until you see POL or SPA. The programmed temperature will be displayed. Press the UP arrow to increase the temperature setting one degree at a time.

Digital Water Temperature Control: The pool water temperature is controlled by the heat pump pool heater’s digital control system, which gives you the option of two settings: one for the desired spa temperature and the other for the desired pool temperature. Additionally, as mentioned earlier, the unit is compatible with most ‘2-wire’ and ‘3-wire’ control/automation systems.

To Lower the Desired Water Temperature (Pool or Spa Mode)

Push the SET key until you see POL or SPA. The programmed temperature will be displayed. Press the DOWN arrow to decrease the temperature setting one degree at a time. Once the control has been programmed to the desired pool water temperature, the programmed temperature will be displayed for approximately 5 seconds. Then the digital display will display the actual pool water temperature.

To make the Board a Pool ONLY Board, call 800260-2758 for instructions.

To Select Temperature in °C or °F

Fig. 5: Digital Water Temperature Control

Defrost Sensor: Prevents unit operation if ambient air temperature falls below a predetermined safe minimum (approximately 42°–48°F (5.5°-8.8°C) based on humidity). The compressor will shut OFF but the fan will continue to run.

Delay Timer: Prevents compressor from short cycling, which could damage or destroy the hermetic motor/compressor. Upon water temperature control satisfaction, or other circuit interruptions, this solid state device will prevent compressor restart for approximately 5 minutes.

Press the SET key until you see F _C. By pressing the UP or DOWN key you can switch to °F or °C. Once the temperature display mode has been programmed it will be displayed for approximately 5 seconds, then the digital display will return to the actual pool water temperature in the mode that you have chosen.

10

Heat/Cool Operation

Seasonal Start-Up or Annual Check

The Raypak Professional models come standard with heat/cool operation. The heat/cool model is designed to both heat and cool the pool. To select heat or cool mode, push the SET key until H/C is displayed. Press the DOWN arrow key to select heating (hea), or the UP arrow key to select cooling (col). Set the desired setpoint temperature as described earlier in this manual.

NOTE: At the beginning of the heating season, or whenever the pool water temperature is to be raised several degrees, the pool pump and heat pump pool heater may need to operate continuously for several days. During summer months, only a few hours per day may be necessary, or none at all.

NOTE: Once the control has been programmed to the desired pool water temperature, the programmed temperature will be displayed for approximately 5 seconds. The digital display will then show the actual pool water temperature.

1. Remove leaves, pine needles, etc., from the evaporator coil. Clean the coil by gently applying a mild solution of household liquid soap and water. 2. Gently rinse the coil with water; DO NOT use high pressure.

NOTE: Remove the pool/spa blanket and turn on any fountains, sprays or other water features to speed cooling.

3. Backwash or otherwise clean the pool filter. If necessary, clean the skimmer basket and pump strainer.

When the unit has been operating in the heating mode for a few minutes, the discharge air temperature should be 8°–10°F (4.5°–5.6°C) cooler than the air entering the unit.

NOTE: If the pool pump and heat pump pool heater shut OFF before the water temperature is raised to the desired level, you must lengthen the running time of both. To do this, reset the time clock dial for the longer running time, or manually operate the pump with the timer override switch. Since the heat pump pool heater capacity and efficiency are both greater at higher ambient air temperatures, run time should be set to take advantage of all daylight hours, when the air is generally warmer.

When the unit has been operating in the cooling mode for a few minutes, the discharge air temperature should be 8°–10°F (4.5°–5.6°C) warmer than the air entering the unit. NOTE: Heating is more efficient during warmer daylight hours and cooling is more efficient during cooler night time hours.

4. Set the valves to ensure proper water flow through the unit.

1. Verify that the Digital Board is displaying a temperature and the pool pump is running and water is circulating properly.

If you do not plan to use the heat pump pool heater during the summer months, secure and protect it as follows:

System Start-Up

Summer Shutdown

1. Turn the unit circuit breaker or disconnect switch to OFF.

2. Verify that the Board is programmed so that the desired temperature of the Pool and Spa is higher than the displayed current water temperature.

2. Leave the valves set the way they are unless additional circulation is required. DO NOT stop all flow through the heat pump pool heater.

3. Allow the heat pump pool heater to operate for a few minutes to stabilize operating pressures and to allow various component temperatures to normalize.

4. Verify that the discharge air temperature is approximately 8°–10°F (4.5°–5.6°C) cooler than the air entering the unit. If not, see the Troubleshooting Section.

3. IMPORTANT: Remember to reset the valves before the next heating season, or the unit will not operate properly.

11

Freeze Protection

Cabinet Care (optional)

If the unit is installed in a location subject to freezing conditions, it is important to protect the water circuit from freezing, just as should be done for the pump and filter.

The stainless steel cabinet is designed for harsh outdoor use and requires little care. However, you can clean it if you wish.

1. Turn the unit circuit breaker or disconnect switch to OFF.

Wash the cabinet with soap and water.

WARNING: Shut OFF electricity to the unit before cleaning.

System Drain-Down

Unplug Condensation Drain Holes

2. With the pool pump OFF, close the external shutoff valves and loosen the inlet and outlet water unions to allow water to drain. Use a Wet/Dry Vac or air pressure to remove excess water.

The unit extracts humidity from the air as it passes through the coil, similar to the way a cold drink outside “sweats” on a hot day. This condensation drains from the bottom of the unit.

3. Loosely re-attach the unions.

1. Routinely check to be sure the condensation drain holes in the base of the unit are not plugged with dirt or debris.

4. Cover the unit with a waterproof cover.

Continuous Pump Operation

2. If condensation becomes a problem, optional drain pans are available from your heat pump pool heater distributor or pool dealer.

It is also possible in some areas to prevent unit freeze damage by operating the pump continuously during freezing weather. However, this results in significantly higher pump operating costs. Further, if a sustained power failure occurs, the unit MUST be drained anyway, or freeze damage could result.

Troubleshooting

If your unit does not operate, or simply does not heat your pool water, Fault Codes on the front control panel, can provide valuable clues as to what is wrong, and may even indicate precisely what the problem is. Always observe these codes before calling a service representative. By reporting on the telephone the Fault Codes that are showing, the service rep may be able to solve the problem without the expense of a service call.

Maintenance

NOTE: The heat pump pool heater MANUFACTURER IS NOT RESPONSIBLE for maintenance adjustments. The following maintenance procedures are designed to keep your unit operating at a high level of reliability. Maintenance must be performed on a periodic basis to maintain warranty coverage and prevent system failures and performance degradation.

A. UNIT IS RUNNING, BUT NOT HEATING



Air Coil Cleaning

Efficient operation depends on free circulation of air through the thin and tightly-spaced fins of the evaporator coil(s). The evaporator must be cleaned whenever it has a buildup of dirt or debris.





CAUTION: To clean the fins, spray gently with a garden hose. DO NOT pressure wash. Doing so will bend the fins and can void the warranty. 12

Is water flow through the unit adequate? Check the unit for obstructions, such as a clogged filter pump strainer, a dirty filter, or valves not positioned correctly. Check the operation of the flow switch.

Is the ejected air from the unit 8°–10°F (4.5°–5.6°C) cooler than incoming air? If so, the unit is extracting heat from the air and transferring it to the pool.

Is water condensing on the evaporator and internal copper pipes? This is also evidence of heat removal from the air. When the air is cool with low humidity, condensation may not be evident.





How long has the unit been operating? During initial pool heating in cold weather, it may require a week to elevate the water temperature to a comfortable level. Normally, it takes about 4 days.

NOTE: The heat pump pool heater will not run when the Remote position is selected on the Pool/Spa selector switch and there is no remote control system attached.

How many hours per day is the unit operating? Remember that the heat pump pool heater only operates while the pool pump is running. Set the time clock to permit 24 hour per day operation. After the desired temperature is reached, return the unit to normal operation of 8–10 hours per day.

C. CONDENSATION SEEMS EXCESSIVE

Heat pump pool heaters can produce a large amount of condensation (water) during operation. If you suspect that the unit is leaking:

NOTE: If the pool pump and heat pump pool heater shut OFF before the water temperature is raised to the desired level, you must lengthen the running time of both. To do this, reset the time clock dial for the longer running time, or manually operate the pump with the timer override switch. Since the unit capacity and efficiency are both greater at higher ambient air temperatures, run time should be set to take advantage of all daylight hours, when the air is generally warmer. •





a. Use a pool chemistry test kit to confirm there is no chlorine in the condensation. Or,

b. Shut the unit OFF and leave the filter pump running to see if the water stops dripping. If the water stops dripping, the unit is not leaking.

Service Call Verification

Is airflow through the unit being obstructed? Restrictions such as shrubbery, tall grass, dirty coils, or any other obstruction to airflow will reduce performance.

NOTE: The Raypak Service number is 800-260-2758. For units in Canada, call 800-268-6966. Before you make a service call, first determine if the problem is:

Is the pool blanket/cover being used? Unblanketed pools can lose up to 10 degrees per night compared to 4 degrees or fewer when a blanket is used. Without a blanket, the total heat gained during the day can be lost overnight.

• •

Are rapid heat losses occurring in some other way, such as high wind, spillage, rainfall, flow through solar panels at night, or a high water table?





Warranty Service

Unit operation (power supply, water flow, or time clock adjustment)

NOTE: The MANUFACTURER IS NOT RESPONSIBLE for these adjustments.

Power Supply

B. UNIT IS NOT RUNNING •

Is the Heat Light ON? If not, then the thermostat setting is not higher than the temperature of the water. Raise the thermostat setting.



Is the temperature display ON? If not, the circuit breaker may be shut OFF or tripped. Reset the breaker by switching it OFF, and then back ON. Verify that the breaker is set and operating properly before calling for service.



Is the thermostat setting and the Pool/Spa setting correct? Verify that the temperature has been properly set on the thermostat, and that it is higher than the current water temperature.

Verify that all circuit breakers are reset and working properly.

If the temperature display still does not light, contact the installing dealer, since it may be a power problem requiring an electrician.

Water Flow •

Have you waited approximately 5 minutes for the time delay? After the unit has been running and then shut OFF for any reason, there is a delay before operation can begin again.



13

Verify that the pool filter is clean to provide good flow.

Verify that valves are properly positioned to allow adequate water flow through the unit.

Time Clock Adjustment

Verify that the time clock is set to permit the unit to run long enough to heat properly. Fault Code OFF LP LP3 HP HP6 PSd

Meaning of Code The desired programmed temperature point is lower than 50°F (10°C).

There is a shortage of refrigerant gas in the unit or a faulty low pressure control, or the ambient air is too cold.

The unit has encountered 3 LP faults within the same call for heat and shut down the unit for protection. If this occurs, you should call for service. There is low water flow in the unit or a faulty high pressure control. Check water flow/backwash.

The unit has encountered 6 HP faults within the same call for heat and shut down the unit for protection. If this occurs, you should call for service. The water temperature sensor is open or may be defective.

dSd

The suction line temperature sensor is open or may be defective.

FLO

Possible causes: • The filter is in backwash position. • The filter pump is stopped. • The filter is dirty. • Shortage of water to pool pump. • Water flow switch may be broken.

FL3 FS FS5 COL

The unit has encountered 3 FLO faults within the same call for heat and shut down the unit for protection. If this occurs, you should call for service. Unit is in the defrosting cycle.

The unit has gone into the defrosting cycle 5 times within the same call for heat and shut down the unit for protection. The unit is in the cooling mode.

HEA

The unit is in the heating mode.

HOT

The unit has gone into a fault mode during cooling.

--

Keypad is pressing down on both buttons. Replace keypad. Table C: Control Board Fault Codes

14

WATER IN (FROM POOL OR SPA)

FILTER

CHECK VALVE

CHEMICAL INTRODUCTION

WATER OUT (TO POOL OR SPA)

Plumbing Diagrams

Fig. 6: For systems with pumps of less than 2 HP (under 80 gpm), no external bypass is required. Connections are 2-inch unions. Plumb the heat pump pool heater AFTER the filter and BEFORE any chlorinators.

15

WATER OUT (TO POOL OR SPA)

WATER IN (FROM POOL OR SPA)

FILTER

CHECK VALVE

CHEMICAL INTRODUCTION

Fig. 7: For systems with pumps of 2 HP or greater (over 80 gpm), an external bypass is required. Adjust the bypass valve to divert a minimum of 40 gpm through the heat pump pool heater. Connections are 2-inch unions. Plumb the heat pump pool heater AFTER the filter and BEFORE any chlorinators.

16

Fig. 8: Pool Piping for Heat Pump Pool Heater and Gas Pool Heater

17

Fig. 9: Pool Piping for Heat Pump Pool Heaters, Multiple, Primary/Secondary

18

2 UNITS BRANCH MAIN 15 GPM 2" 2" 30 2" 2" 45 2" 2" 60 2" 2-1/2" 80 2" 3" *Sizing based on 10 ft/sec flow rates

MINIMUM PIPE SIZES 3-4 UNITS BRANCH MAIN 15 GPM 2" 2" 30 2" 2-1/2" 45 2" 3" 60 2" 3" 80 2" 4" 15 GPM 30 45 60 80

5-6 UNITS BRANCH 2" 2" 2" 2" 2"

MAIN 2" 3" 4" 4" 5"

Wiring Diagram 208V/230V 3Ph, 60Hz Models

19

Wiring Diagram 460V 3Ph, 60 Hz Models

20

Wiring Diagram 380V 3Ph, 60 Hz Models

21

Installing a Remote Control Device Wiring For a 2-wire control, use the TOTAL and COMMON connections on the heat pump pool heater wiring block.

For a 3-wire control, use the COMMON, SPA and POOL connections on the heat pump pool heater wiring block.

Fig. 11: Heater Wiring Block

Heater Settings

1. Make sure the heater is disabled on the remote control device. Then, push the SET key until POL is displayed. Push the DOWN arrow key until OFF is displayed. Wait until a temperature is displayed before beginning the next step. 2. Push the SET key until SPA is displayed, then push the UP arrow to 104°F. Wait until a temperature is displayed before beginning the next step.

3. Push the SET key until P_S is displayed, then push the DOWN arrow until POL is displayed. Wait until a temperature is displayed before beginning the next step. 4. Finally, enable the heater on the remote control device. When there is a call for heat, the heater display will show SPA. When the heater is disabled, the display will show POL.

22

23

Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 Fax (805) 278-5468 Heat Pump Service 1-800-260-2758 Litho in U.S.A.

24

Loading...

Heat Pump Pool & Spa Heater - globalimageserver.com

INSTALLATION & OPERATING INSTRUCTIONS Heat Pump Pool & Spa Heater Professional Series PS10353ti-E-HC PS10354ti-E-HC PS10355ti-E-HC R C LI S TED U...

2MB Sizes 0 Downloads 0 Views

Recommend Documents

Gas-Fired Pool & Spa Heater
The manufacturer recommends that this manual be reviewed thoroughly before installing your pool/spa heater. If there are

Gas-Fired Pool & Spa Heater - Pool Heaters
This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future ....

Gas-Fired Pool & Spa Heater - parts4heating.com
SERVICING INSTRUCTIONS. 31. General Location of Controls. 32. Control Panel Removal. 32. Control Adjustments - Digital a

Raypak Digital Pool And Spa Heater
The Raypak Digital has on-board diagnostic controls that let the user and the service professional know what is going on

Hayward Pool Products - Heat Pump Troubleshooting Guide
Water flow issue. Heater requires a minimum flow of 30 GPM. The water pressure switch is not sensing pressure. Is filter

Pool Pump Sizing Calculator - Salt Water Pool and Spa
The larger the pump the more flow is generated and subsequently the faster turnover rate. Turnover rate is the period of

Electric SPA-PAK Heater - globalimageserver.com
It is essential that the heater be installed in accor- dance with the instructions given herein. Failure to do so may ca

Pool Pump Calculator - Ausgrid
Use this calculator to estimate the cost of running your pool pump and find out how much you could save on time-based pr

Pool Pump Calculator | EcoPump
Compare Your Pool Pump's Efficiency to EcoPump. Get a detailed Energy Efficiency Report and pump recommendation in just

Rheem Pool Heater Error Codes Sns - WordPress.com
Website hosting, Domain, Developers blog, Dedicated, Reseller hosting, Domain types, Server… how do i reset my raypak