Cloudy Pool Water Issues | InTheSwim Pool Blog

InTheSwim Pool Blog

Cloudy Pool Water Issues July 9, 2013

Mike Cummings

As a former pool store manager for over a decade you can trust that I’ve heard my fair share of “My water’s cloudy, what can I do?” In fact it was the number one issue – day in and day out. And it was my job to figure it out. There would be folks waiting in their cars before we opened and pounding on the door after we closed, with water bottle samples in hand, looking for solutions to their cloudy pool water problems. Keeping a pool clear for most pool owners can be a struggle, especially new pool owners; those who get improper advice or follow the wrong procedures, or when you start with an especially yucky pool from the getgo at opening. So what causes cloudy pool water, what are the remedies, and what is the best preventative treatment to keep your water sparkling clear? POOL OPENINGS: Some common causes are simply part of the pool opening process. After not filtering for six months, what would you expect? What often happens is when you have a solid winter cover for your above ground or in ground pool and you don’t pump every last bit of the yucky water off the top, so that when you try to remove the cover, the last 10+ gallons of nasty water that’s saturated in leaf debris, tannin, algae, and bugs is too heavy to lift, and ends up in the pool! That concentrated slimy water hits the pool and explodes outwards and clouds up the entire pool in a matter of seconds so that it looks as if you may as well have not covered it at all. Afterwards. it’s on to spending a small fortune on pool shock and other chemicals, hours of vacuuming, and scooping out leaves. Wasting water backwashing or rinsing down cartridge filters. All of which is what you need to do to turn the pool around when this happens. That used to happen to me every other year until I purchased a nice lightweight safety cover that’s a snap to lift off because water and snowmelt drains through and the leaves blow away. MINERALS & METALS: There are other ways a pool can cloud at opening for instance simply topping the pool off can be a potential problem for some. Untreated well water is often used by rural pool owners and can be laden with minerals, iron, and other metals that have soaked into the ground and ended up in the well. These things can leave a brown tint to the water and leave orange rust deposits on your skimmer & pump baskets, trim frames and ladder bumpers, vinyl liner, and just about any pool surface. If left unchecked, these can be a source for murky water and lead to permanent stains. A garden hose filter is a handy device for pre-filtering minerals and metals. It’s an inline strainer that you thread onto your hose that absorbs iron and scale before it can get in the pool. Another remedy is to apply a stain and scale remover. Many brands are available that sequester or chelate (from the Greek word for claw) out the metals so your filter can trap them, while an acid in the chemical formula breaks down scale (calcium). This product should be used whenever water is added to remove metals and break down scale and is often included in pool opening and closing kits for pools. WATER BALANCE: Another common occurrence is to have unbalanced water with unusually high or low pH, Alkalinity, Calcium Hardness, Stabilizer (cyanuaric acid), TDS (Totally dissolved solids), or chlorine. You may have any one high and another low or a combination of all of the above being out of whack. A good rule of thumb is that anything high can cloud a pool so bring down the levels to the low end of their range. Another rule of thumb is to balance Alkalinity First, and then move on to pH next. Alkalinity is increased with Sodium Bicarbonate and reduced with Muriatic Acid. Low pH can be adjusted with Soda Ash, high pH with Muriatic acid or Sodium Bisulfate. Calcium hardness is increased with Calcium Chloride and reduced with a stain and scale remover. Cyanauric Acid is reduced only by draining and replacing water. Note that sometimes high CYA causes cloudiness and sometimes it does not. High TDS can contribute to cloudiness and should be within the recommended range in the manuals for mineral systems, Power Ionizer, and salt system owners. TDS is essentially anything dissolved in the water except H2O. The acceptable range is wide at 0-2000 ppm. So once you have tested and balanced these things and cloudiness still persists, then we must explore some other scenarios which I will try to explain without any opaque utterances so that you can have a clear understanding. TOO MUCH SHOCK? One such scenario is over-chlorination and over-shocking which often leads to doing more harm than good. I had many a customer dumping more and more chlorine & shock in their pool to try to clear it up not knowing that this process can temporarily cloud the pool as a side effect of doing its job. And if you don’t wait between treatments the cloudiness just overlaps the next treatment so you never get any results. Like taking two steps forward and three steps back. Some people would go all summer without ever clearing up the pool because they didn’t wait between treatments. Another mistake that goes hand in hand with this is to measure your chlorine too soon after shocking. What happens is that the chlorine is so high that it “bleaches” out the test. Test strips and residential reagents are not designed to measure extremely high levels of chlorine and the super-chlorinated water literally bleaches out the test strip pad or disintegrates the reagent in your test vial so it appears there is no chlorine in the pool and the homeowner hits it with more chlorine and more chlorine making it more and more cloudy. That’s when it’s time to stop, wait, test, then shock with the right dosage.

Shocking the Pool for Cloudy Water Nine times out of ten all you need to do is shock. But – you need to dial in the correct amount. And when you shock the pool, do it properly to reach what is called breakpoint chlorination. What this means is that you are going to raise your chlorine level to 10 times the level of combined chlorine. Combined chlorine is the accumulation of chloramines or chlorine that has attached itself to organics such as algae to suffocate it, ammonia from oils, debris, and bather waste, and all of the yuck that fell in from that solid winter cover mishap at opening. Combined chlorine = Total Chlorine – Free Chlorine. DPD test kits will test for combined chlorine, while OTO test kits and test strips will only test for Free Chlorine levels. Chloramines build up in the pool until you give it a good shocking to burn or oxidize it away. OXIDATION: What is oxidizing and where do the chloramines and yuck go? Pour too much bleach on a shirt and what does it do? It eats a hole in it right? Where did the material go? Poof! It’s just gone! Well that’s oxidizing. Some call it “burning off.” Now, the amount of pool shock it takes to reach breakpoint depends on your pool gallons and combined chlorine level and a common problem is that today’s ever-popular vinyl lined pools cannot handle the required amount as they will damage and fade the liner over time. Painted pools can handle a great deal more but can fade and plastered pools can be blasted to no end. With fiberglass pools, you should be slightly more… conservative in your dosage. HOW MUCH SHOCK? A good rule of thumb is to use one bag of shock per 10,000 gallons or 1 gallon of liquid chlorine. To be quite honest you have to “play” with the strength depending on your pool problem but a safe bet is to hit it with the 1 bag per 10K – plus 1 more bag, so you get there without damaging your liner. So you take 3 steps forward and just 2 back. If that doesn’t do it, wait 1-3 days to make sure the level goes down and do it again. Now it’s 3 steps forward and 1 back. On the third shock you are 3 forward and 0 back. Now you are done and regular chlorine tablets or any other sanitizing methods like calcium hypochlorite should keep it sanitized and clear! Shock and chlorine will wear off faster with intense sun and less when the there is no sun. I always brush the pool floor and walls, then shock. Repeat until clear. Different levels of cloudiness demand different amounts of shock and I have come to know my pool and if it’s green with visible algae – I double the dose. If the pool is very cloudy, way past hazy to milky – I increase the 1 bag of shock per 10K rule, and if it’s a weekly shocking, I do the 1 bag per 10K. My pool stays clear all summer long as long as I check it every day. That’s the secret. Just a quick glance before or after work and if it’s starting to turn, it’s time to brush & shock.

“I tried all that. What else is there?!?” FILTRATION: Another potential scenario may be that your pool filter is not doing its job. The filter media could be worn, or water could be bypassing the filter media, and returning to the pool unfiltered. SAND: If your sand is more than 5 years old, or has never been changed at all, then it should be changed. Old filter sand can sometimes clump and the water channels down the tank sides or between the clumps which causes poor filtration. You can also clean your sand each year with sand cleaner to rejuvenate it. This eliminates calcium build-up, oils, and organics that tend to cling to it. Fresh sand grains are square and edgy and when packed together, and effectively trap debris. But, as they are pounded by water they smooth out like rocks on a beach and lose their dirt trapping capability. CARTRIDGE: If your filter cartridge is more than 3 seasons old it may be time for replacement filter cartridge. The membranes become clogged with oils, lotions, calcium, scale, and dirt. They lose their effectiveness as they become fuzzy, the straps break, the end caps get sticky, or they start to collapse. If you can afford it, buy a new one at the start of each season and use the old one for spring cleanup and then toss it out. Once a year, the pool inside of my pool store used to become cloudy beyond fixing with chemicals. Since I had a myriad of chemicals at my disposal, I tried them all! I would put in a new cartridge and voila! It would clear right up. DE filters should also be monitored for performance issues. DE grids or fingers should be cleaned with Filter Cleaner periodically, at least annually. Manifolds and pressure plates should be inspected for cracks where debris can slip back into the pool. But for the most part a properly functioning DE filter will clear a pool quickly and keep it that way. WHAT ELSE? But what is there to do if you have a successful cover removal, balanced the chemical properties properly, cleaned or replaced your filter, and yet the problem persists? Turbidity is a fancy word for water that is not transparent because of stirred up sediment and also just so happens to mean confused, muddled, or disturbed ( which incidentally is just exactly how pool owners come to feel when dealing with cloudy pool water. Especially when they have a family and kids who want to use the pool, its 90 degrees out, and they can’t – for safety reasons. CLARIFIERS:To effectively remove this sediment there is a method that is much less harsh than shocking. You simply apply a clarifier or super clarifier which is sold in quart, ½ or 1 gallon bottles and in a variety of brands. Clarifiers work best with sand filters and act as a coagulant to bond suspended particles together so they are bigger and more easily captured by your filter. Clarifiers are also available in a gel, or gelatinous cube like Mira-clear which can be placed in your pump basket, erodes into your filter to fill the gaps in the sand, and trap fine particulates. All of these clarifying agents are designed to clarify your water so it has that sparkling clear essence that allows us, as the saying goes, “to read the date on a dime” dropped on the pool bottom. FILTER AIDS: And then there are some common filter aids like Synthetic DE, most often called Perlite or AquaPerl, which can be added to a cartridge filter by sprinkling a small amount into your skimmer, which effectively brings your cartridge down to a much smaller micron filter. FLOCCULANTS: Another solution to try is a good pool flocculant. This phenomenal pool chemical is available as a liquid or powder that you apply directly to your pool and allow it to circulate, then turn your filtration system off and it weighs all of the sediment to the bottom of the pool so you can vacuum it up. It is best to vacuum it all to waste because the gummy residue will quickly clog up your filter, requiring frequent backwashing. AND FINALLY there is a tip that people usually have a hard time believing. That is to use the pool! Swimming and Splashing around gets that water circulated and into the skimmers and main drain better than anything else. Your pump and filter can only do so much to turn over all the of gallons in the pool mathematically in 8-10 hours, but does not necessarily turn over ALL of the actual water. Unless you are brushing daily, or have an automatic pool cleaner going, some water sits in stagnant zones and may not get filtered. Sometimes it’s hard to get people in the pool when it’s cloudy but it will help. You just need to keep a sharp eye on all swimmers – and No Diving! Once my pool is clean & clear I try to use it every day. This keeps it stirred up, ensures that I get a chance to inspect it, and I give it a quick test with test strips to make sure it is balanced. So using the pool, daily inspection, and a once-a-week shock treatment are my secrets to clean and clear pool water. So to recapitulate, and continue to curtail the cloudiness, remember it’s a combined effort of filtration, water balance, sanitation, circulation, frequent pool use and – maybe finding the right accessory chemical to help coagulate and trap suspended particles. That is my step-by-step to remove cloudy pool water so you and your family can enjoy a sparkling clear pool!

Mike Cummings InTheSwim Staff Blogger RELATED PRODUCTS:

permalink []

About Mike Cummings Internet Merchandiser at In The Swim, Swimming Pool Enthusiast View all posts by Mike Cummings

Comments Cloudy Pool Water Issues — 32 Comments

Steven Wright on January 18, 2018 at 2:24 pm said:

our pool guy told us that it is a common thing for our pool to get cloudy years after being resurfaced. we had done about 5 years ago, now the water is becoming cloudy and continuing to get cloudier. He, our pool guy, has recommended draining the pool and refilling it. any thoughts? Davy Merino on January 19, 2018 at 8:49 am said:

Hi Steven, cloudy pools are not uncommon, but nothing to do with the plaster, except in the first few months after plastering. It could be from very high levels of total dissolved solids, hence the suggestion to drain and refill. Fresh water every 5 years can make pool management easier, no doubt about it. Another key factor to water clarity is the effectiveness of the filter, and the number of hours running each day. Over time, filter media (sand or cartridges) wear out and need replacement, as they can no longer trap the really small particles. Finally, water balance (pH, alk, calcium hardness) is an important component, when water is not balanced, it can precipitate normally invisible minerals and make cloudy water. And chlorine levels too – if they drop too low, you will quickly see cloudy water. So, although draining and refilling will likely help, take a look at these other causes of cloudy water – filtration, circulation, sanitation and water balance – to fix the full problem. Steven Wright on January 19, 2018 at 11:44 am said:

thank you Davy. this guy just took over the business and has started using dry chlorine instead of liquid. our filter is only a couple of years old and is well maintained. Im thinking the switch to dry chlorine and the amount of time we were getting away with running the filter using the liquid may be the culprit. I am going to increase the time and see if it helps. we have never had a problem before and when I say cloudy, I can see the bottom very well, its just starting to get “that look” I’ll keep you posted. Thank you again for your quick reply. Davy Merino on January 19, 2018 at 4:37 pm said:

Hi again – if by dry chlorine you mean granular chlorine, that could cause water cloudiness in two ways – first, it’s likely cal hypo, which contains calcium and if your pool has very high calcium levels already, it can take awhile for the calcium to dissolve, secondly using granular chlorine to sanitize a pool is not good because the level goes high very quickly, then tapers off rapidly, resulting in peaks and valleys of chlorination, and during a low valley, the water begins to turn hazy, until he shows up and zaps it again. Slow feeding chlorine tablets through a chlorinator, or using 5-gal liquid chlorine WITH a chlorine pump is the best way, to chlorinate consistently throughout the day.

Zoe on July 13, 2017 at 9:54 pm said:

Hi, we just recently shocked, and treated with algaecide our vinyl pool and came back the next day to find large, white strips, or “wisps” floating in the pool. We have no idea what it is, and don’t know what our solution could be. Davy Merino on July 14, 2017 at 8:28 am said:

Hi Zoe, not sure either, could be ‘white mold’, or some sort of reaction occurs between shock and solids, or perhaps the algaecide, coupled with a high pH. Skim out the stuff, run the filter overtime, and apply a dose of clarifier to help. Keep chlorine level high and pH level low.

Kristi on July 12, 2017 at 7:25 pm said:

Hi! We have a metal frame pool, holds 3500 gallon. We use a salt water system. We recently had to replace the pool pump itself. Now our pool is a cloudy green color. I’ve shocked it, added a clarifier, baking solda, algicide…you name it’s been put in the pool. Today I checked the levels and the chlorine level is at a 10, clearly can’t swim in this. I turned off the salt water pump and left the regular pump running. How can I get rid of the cloudy green color, I want my pretty clear blue pool back overly frustrated! Davy Merino on July 13, 2017 at 8:53 am said:

Hows the filter cartridge? Might need to be replaced – those tiny things only last about 3 months, and if they have to deal with heavy work, like algae, they can fail. Also, are you running the pump 24/7, to help clear the water faster? When it’s really hot (like now), those little pumps need to run longer, at least 12 hours per day, if not more. If the water is still green, you need more shock, even though it reads 10 ppm, if the water is still green… needs more shock. Add 1.5 gals of bleach, or 1.5 lbs of pool shock. Be sure pH level is 7.2-7.4 before shocking. If there is sediment or debris on the floor, vacuum before shocking if possible. Brush pool, filter 24/7, add clarifier the next day, use algaecide only when chlorine level drops to normal ranges, high levels will destroy algaecide. Kristi on July 13, 2017 at 10:56 pm said:

It’s a brand new filter we put in when we replaced the pump! Should I use a chlorine free shock since my chlorine is so high? It’s starting to look milky green now Davy Merino on July 14, 2017 at 8:31 am said:

OK, good that the filter is new – you may need another after this episode is passed – use chlorine, not non-chlor, 10 ppm is high, but you need to go to 30 ppm to kill the algae, and then you need lots of filtering and cleaning.

Chris on July 7, 2017 at 7:04 pm said:

A German chocolate cake with lots of coconut ended up in my pool. Pool is milky and oiled. Any suggestions? Davy Merino on July 8, 2017 at 3:39 pm said:

Wow, that’s a good one. Enzymes are the ticket for oily gunk – Pool Perfect is the classic pool enzyme, by Natural Chemistry. Pool First Aid can also be used. Keep the insides of the skimmer scrubbed out clean, that will reduce scum line around the tile, and run the filter overtime. Check and balance all chemical levels, and elevate chlorine somewhat. You’ll get it back, and always have a funny story to tell.

Craig Jefson on July 7, 2017 at 8:32 am said:

Good Morning Mike, First, appreciate your Blog and the information you are providing pool owners. Second, I have a pool situation I would be interested in hearing your response to…gunite pool, chlorine tablets, running pump about 16 hours a day, automatic cleaner, cartridge filter cleaned (pool company cleaned and soaked filters), etc. Recently had my pool water tested. The CYA level was at 95 about 2/3 weeks ago. Used cyanuric acid reducer and tested the following week, level was a 90. Tested again yesterday and its down to 80 (progress?). It was also suggested I scrub the walls and pool floor. When I did this the pool became cloudy (milky). Pool company said this was probably “dead algae” (pool never turned green, actually always clear blue) and that I should shock it and allow the pool pump to filter the water. I did this about 4:00 pm yesterday and this morning the pool water is much less cloudy (more of a light haze). I would appreciate any feedback you can provide (e.g. on the right track?; anything I should do currently?; suggestions moving forward…shock weekly, scrub weekly, etc. Thanks for being available and for any feedback you can provide. Craig Davy Merino on July 8, 2017 at 3:47 pm said:

Hi Craig, glad to see that the cyanuric acid reducer works a little bit, although it claims to reduce 50 ppm, per treatment (Bio-Active). If possible to replace some of the water, a foot or two, that is another way to reduce cya levels, and also reduces total dissolved solids. For the cloudy water – from brushing the pool, I guess the pool walls were just very dusty? Maybe a good vacuuming to waste could help. Or just start brushing it weekly, it’s good for the plaster, and good exercise for you too. Shocking weekly is not needed, unless you have visible algae, measureable chloramines, or allowed chlorine levels to drop to zero, or for pump problems, filter problems, or after a large party with numerous swimmers for many hours, or if the pool becomes contaminated with something yucky – other than that, if it looks fine, no need to shock, save your money.

Victoria Hodgson on June 26, 2017 at 9:53 pm said:

Hi,I don’t know what’s going with my above ground pool,my water is so cloudy even I can’t see the bottom.I s been like that for over a week I shocked with almost 4lb and remains the same.please advice. I got my water tested and told everything is okey!!! Davy Merino on June 27, 2017 at 8:45 am said:

Hi Victoria, probably a filter issue. When the water is spot-on balanced, and the chlorine level is good and steady – look at the circulation and filtration. Could be time for a new filter cartridge or filter sand. Clarifiers can be used to help your filter trap small particles more effectively, but be careful not to overdose. Purifiber can be used as a filter aid for cartridge filters, just a cup added to the skimmer. Alum (Aluminum Sulfate) can be used as a flocculent for extreme cloudy water, very effective but you must be able to vacuum to waste, the following day. Not related to filtration, but for pools with high levels of dissolved solids (TDS), draining and refilling half of the pool can often be a big help, to remove half of the solids and suspended material, which can help the filter out tremendously.

Martha on June 23, 2017 at 6:15 am said:

just bought a new sand filter when we started it up a it blow out a cloud of dust and days later our pool is very cloudy we tried balancing but nothing is working the pool has been on day in day out Help the kids want to swim Davy Merino on June 23, 2017 at 6:54 am said:

Hi Martha, sand filters often blow out a lot of ‘sand dust’ upon initial start-up, with new sand. Starting the filter on the Rinse setting will avoid this. Unrelated to your cloudy water issue – unless one of the laterals in the tank bottom is releasing sand – if you find sand in the pool, constantly, not just a handful after startup, the laterals or standpipe in the filter could be allowing water to bypass (not filtering the water). Also could be caused If the wrong type of sand was used (should be #20 silica sand, .45-.55 mm graded, labeled “Pool Filter Sand”). Other issues could be plumbing the filter valve incorrectly. the PUMP port should connect to the pump pipe and the RETURN port should connect to the return line. Third issue with cloudy water, since you are running the pump 24/7, should be poor water balance or low chlorine levels, or possibly high levels of phosphates contaminating the water. Assuming that the filter is not undersized, you can use some clarifier to help the filter trap small debris (with good water balance and chlorine levels too).

Wade on June 22, 2017 at 8:11 pm said:

Mike, I overdid my 14 foot above-ground pool on soda ash to raise the pH and overall alkalinity, and now I can’t see anything beyond the top. I treated it about 11 hours ago and no change. Any suggestions to clear it up, and is it safe to swim in? My numbers on the strip test are good except calcium is low, but I don’t plan to mess anymore with that until I can figure out what to do about the murkiness. Thanks! Wade Davy Merino on June 23, 2017 at 7:12 am said:

Hi Wade, carbonates and bicarbonates often make good water clouding materials. If your pH and/or alkalinity is now too high – lowering it with acid may reabsorb the carbonates into solution. I would adjust the calcium hardness too, if very low (under 150 ppm), that could be contributing to the problem. Clarifiers can also be used, to help trap the material in the filter for backwashing.

Cheryl on June 22, 2017 at 3:00 pm said:

Pool was clear when we opened and has stayed clear until just yesterday. the chlorine levels were high and ph was a little low so we dialed down the level of chlorine. opened pool yesterday and it was cloudy and no chlorine is registering. We turned up the level of chlorine and shocked the pool. How long will it be before we should see a chlorine reading. We are thinking of adding liquid chlorine today. Any help would be great. Davy Merino on June 23, 2017 at 8:03 am said:

Hi Cheryl, you should see a chlorine reading immediately after adding shock chlorine. Well, maybe a few minutes for it to disperse, but right away. If you add chlorine, possibly a lot of chlorine, and see no reading on your test… 1) bad test strip or reagent, 2) chlorine demand is higher than supply (something is consuming it) 3) no stabilzer in the pool, add 4 lbs of cyanuric acid per 10K gals 4) too much stabilizer in pool, keep it 20-50 ppm, or 5) pool water needs more filtering each day, or filter media is old/dirty, or filter/valve problems are allowing water to bypass filter media. Very often, it is a combination of more than one of these. Hope this helps (saw your other post too) – Davy

Tina on June 19, 2017 at 7:44 pm said:

My pool is very cloudy I guess that milky or blur gray. It started very green I have green cleared I have Brushed, vacuum been in it put tons of shock, chlorine raised all levels up not sure his go get acid up it is testing low on that Had water tested they tell me phosphate levels are high (3417) I’ve done flocculant which did nothing Water isn’t clear I can’t see what’s on bottom and really don’t want to get back in until I can see bottom. Any suggestions ? I just shocked About 4-5 days ago did 5 bags of shock have 30k water I have shocked pool numberous times last month not had clear water since I took top off Any help would be appreciated Davy Merino on June 20, 2017 at 8:35 am said:

Hi Tina, 3417 phosphate level is 11x the suggested minimum level of 300 ppb. I would treat the pool with The PhosFree Extra Strength, following label instructions carefully. If you can’t drain the pool and refill it, which is also a valid suggestion. There is some sort of extreme contamination going on, perhaps nearby mulch beds or planters are overflowing into the pool. Perhaps fertilizer found it’s way into the pool from backyard landscaping efforts. Perhaps the fill water for the pool (from the hose) is contaminated. This should be addressed or you will have continued problems with algae and cloudy water. After treatment of Phosphate remover, retest the levels, you can buy your own $10 phosphate test kit. The pool may need several treatments to remove such a high level of phosphates, so if you can drain or partially drain and refill, that would get you swimming much sooner, and give you less problems down the road. Especially if the pool water has not been changed in over 5 years, it likely is choked with many other solids, beside phosphates and nitrates, which is contributing to the cloudy water conditions. But if draining is not possible, bring the phosphates down below 300 ppb, and then shock the pool – hard – 9-12 lbs would not be unusual in a pool your size. And… try to solve the phosphate mystery, what has contaminated the pool? It could happen again if you don’t find out!

Anon505 on June 16, 2017 at 4:32 pm said:

Accidentally put 2 bags of shock (some website said the pool had 20,000 gals, in reality it’s actually 8,000 gals. Each bag was 10k worth. Should I dump all the water and restart? Davy Merino on June 18, 2017 at 9:55 am said:

Hi, no need to drain. It will come down on it’s own over time. A few days usually. No problem.

Doretta Braden on May 29, 2017 at 7:13 pm said:

Our pool was green when we opened it. Added lots of chlorine and got the green out but now it’s so cloudy we can’t see the bottom. We backwashed several times trying to clear up the green and now realize we forgot to rinse. I suspect the cloudiness is due to that. I’ve used a clarifier with minimal results. Should we brush the sides & bottom or try vacuum to waste or try a floculant? Davy Merino on May 30, 2017 at 6:38 am said:

Hi, Rinsing doesn’t do much – probably not the cause, there is just a lot of material that is overwhelming the filter. If there is a noticeable sediment layer on the floor, vacuuming to waste is a good idea. If not much, then brushing would be preferred. Other tips to clear the water – run the filter 24/7, balance the water chemistry (ph, alk, calcium, cyanuric), and resist the urge to backwash the filter, until the pressure gauge is 5-7 lbs above the clean pressure, or until water flow is noticeably diminished. You can retreat with a clarifer after 5-7 days of a previous treatment. If no better after a week, you may consider replacing the filter sand.

Monte on May 20, 2017 at 8:06 pm said:

The salt cholorinator stopped working. Cloudy Algae looking water. Water took down turn. Shocked then chorine nothing changed. Raised my alkalinity from 40 to 90 ppm with soda a. Raised ph to low end. Plenty chorine available. Still shows it needs soda ash some. Add more soda ash or give it a day or two. 26,000 ga pool approx Davy Merino on May 21, 2017 at 12:08 pm said:

If you are still trying to kill, algae – the chlorine is much more effective at a 7.0 – 7.2 range. So, I’d probably keep it low until the water starts to clear. If the pool is still green, shock again, but keep adding it until the water turns a blue/grey color, and stays that way. If it still has a tinge of green, or if the chlorine level drops to zero after 8 hours, you need to add more shock, to make a complete kill or oxidation of the algae.

curtis on April 18, 2017 at 7:33 am said:

Got one for you Mike…We had to drain most of pool this spring and do a lite repair, due to the cost of a refile or we had to use well water we decide to pump water out of the creek. The creek looks like ice tea ie: tannin colored, what if anything can be done to clear this water. I do have to add when you scoop out a class of water it looks clear…Thanks in advance Curtis Davy Merino on April 18, 2017 at 11:07 am said:

Hi, I’ve had a friend of mine fill his pool from the creek. I thought he was nuts, but it turned out OK. It was a little murky and tan colored at first, but he tested and balanced the pool water, and circulated a metal out product (sequestering agent) and some clarifier overnight, and then shocked the pool to a blue color the next day – no problems!


Cloudy Pool Water Issues | InTheSwim Pool Blog

InTheSwim Pool Blog Cloudy Pool Water Issues July 9, 2013 Mike Cummings As a former pool store manager for over a decade you can trust that I’ve he...

NAN Sizes 6 Downloads 22 Views

Recommend Documents

cloudy pool water: clearing hazy pool water, green pool water
Oct 23, 2017 - There is no one cause of cloudy, dirty, hazy, murky, gray, milky, muddy or dull pool water problems: susp

Pool Pump Sizing Calculator - Salt Water Pool and Spa
The larger the pump the more flow is generated and subsequently the faster turnover rate. Turnover rate is the period of

Nature 2 Fusion issues - Trouble Free Pool
May 15, 2015 - Nature 2 Fusion issues. SO I have a brand new pool - got a SWG to make my life "easier". It's been anythi

Gas-Fired Pool & Spa Heater - Pool Heaters
This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future ....

A. Calcium Hypochlorite - 65-75% available chlorine. B. Chlorinated Isocyanurates - varying percentages of available chl

POOL SCHEDULE. *Members must exit the pool area for maintenance. 8:15-8:30am. 10:40-10:55am. Lap Swim*. 5:30–6:30am 4L

Swimming Pool and Spa Water Chemistry
Oxidation. Superchlorination. Combined chlorine. Breakpoint chlorination. Inorganic and Organic Chlorine. Effect of pH o

Pool Carriers - WCRIBMA
The following is a list of the designated pool carriers in alphabetical order. This list combines the two types of pool


Pool Pump Calculator | EcoPump
Compare Your Pool Pump's Efficiency to EcoPump. Get a detailed Energy Efficiency Report and pump recommendation in just